HOME
ABOUT US
CALENDER
MEMBERS
GALLERY
CONTACT
Model Steam Road Vehicle Society Ltd
ADDRESS
In the first instance please telephone or email us, see below.

Membership Secretary
Steve Orchard.
PHONE 01453 546830

or Chris Ward
EMAIL, chris ward
your email will be passed onto the relevent committee member for a response

Content of this web site is copyright to MSRVS Ltd, or Chris Ward

Recommended Preparation by Members for the Boiler Test Events.

Preparation by Member for Boiler Hydraulic Test Against 2008 Blue Book (revised 2006 Red Book)
All of the following should be carried out prior to presenting your engine to the boiler testers.
If possible complete your own test at home before the club test.
Make sure that the boiler pressure gauge can be isolated during the test.
Make sure that the boiler pressure gauge can be calibrated, on or off the engine.
Whichever way is used the fitting must have a 1/8" BSP male fitting on the boiler or gauge
to suit the boiler testers pressure test kit. You might have to make a suitable fitting.
The boiler must have a 1/8" BSP male fitting to suit the boiler tester's pressure test kit.
Make sure that the safety valves can be isolated, removed and the connection blanked, or
gagged for the test.
If the boiler has been stored wet with concentration of corrosion inhibitor greater than the
recommended minimum the boiler should be drained and refilled, excluding all air, with the
recommended minimum concentration of corrosion inhibitor. (This is to avoid drainage of
excessively dosed water onto the test site during draining off some of the boiler water prior
to raising steam.)
Bring last year's boiler test certificate and record card with you.
Members must present their "paid up" membership card.     

Preparation by Member for Boiler Steam Test Against 2008 Blue Book (revised 2006 Red Book)
All of the following should be carried out prior to presenting your engine to the boiler testers.
 If possible complete your own test at home before the club test.
 Make sure the safety valves are working correctly.
 Make sure that both/two methods of putting water into the boiler under working conditions are working correctly.
 Make sure that the boiler pressure gauge can be calibrated, on or off the engine. Whichever way is used the fitting must have a 1/8" BSP male fitting on the boiler or gauge to suit the boiler testers pressure test kit. You might have to make a suitable fitting.
Fill/Drain the boiler with water containing the recommended minimum concentration of corrosion inhibitor. (The recommended minimum concentration of corrosion inhibitor is to be used avoid drainage of excessively dosed water onto the test site during draining off of the boiler water prior to or following the steam test).
Bring the previous boiler test certificate and record card with you.
A spark arrester must be fitted for the test.
You must have the boiler volume available to the boiler tester (preferably in litres).
Members must present their "paid up" membership card.                Boiler Test Inspector Team

GETTING TO MSRVS BOILER TEST DAYS AT BRITISH ENERGY BARNWOOD OFFICES - OVERFLOW CAR PARK

British Energy Barnwood Office, Barnett Way, Barnwood, Gloucester GL4 3RS
Barnwood offices are located on the eastern side of Gloucester, about two-and-a-half miles from the city centre, just off the A417 bypass. The boiler tests are taking place in the "Overflow Car Park".

From the North
Leave the M5 at Junction 11, and follow the A40 in the direction of Gloucester. At the first roundabout you approach, take the second turning on the left (A417 Southbound). At the second roundabout, go straight across, and enter Barnett Way, with the Cheltenham & Gloucester building on your left. The Barnwood office is directly in front of you.

From the South
Take Junction 11a off the M5, and follow the A417 in the direction of Gloucester. At the first roundabout, take the second turning on the left, and follow the A417 bypass. At the second roundabout, take the first left into Barnett Way. The Cheltenham & Gloucester building on your left. The Barnwood office is directly in front of you.